Summary
Assess cracks before committing to concrete polishing, but do not assume every line needs the same repair. The decision depends on what caused the crack, whether it is still moving, the condition of its edges and the intended floor use. A surface filling can address a gap without resolving movement in the slab. Identify joints separately, agree any further assessment and treatment, then plan the polishing sequence.
Superfloor Australia · Published 31 October 2026
You have lifted the old flooring and found a crack across the slab. Before booking polishing, it is tempting to buy a filler or ask someone to make the line disappear. A better first step is to establish what the line represents and what you need the finished floor to do.
Superfloor Australia’s polished concrete flooring service in Brisbane considers the existing slab and the proposed finish. Tell the contractor about cracks at the enquiry stage, while the preparation and any separate assessment can still be included in the scope.
Start with the crack’s history
Bring together anything you know about when the crack appeared, whether it has changed and what work has happened nearby. Older photographs can be useful alongside a current view of the whole floor and a closer view of the line. Show its location rather than supplying only an isolated close-up.
Do not turn a measured width into a diagnosis. A single photograph cannot establish whether a crack is dormant, whether the underlying cause continues or whether specialist assessment is required. Ask who will make that decision before the floor is treated.
The International Concrete Repair Institute’s concrete repair terminology distinguishes an active crack, where movement or its cause continues, from a dormant crack whose movement will not affect the repair. That distinction matters when selecting an approach; a narrow line is not automatically a dormant one.
Separate the purpose of the repair from the finish
Ask what the proposed work is intended to achieve. Is the concern a vulnerable edge, a gap that traps dirt, a change in level, an appearance preference or a problem requiring investigation? “Fix the crack” does not describe which of these outcomes is included.
The Concrete Society’s guidance on remedial repair of floor cracks separates work for floor serviceability from a full structural repair. It also explains that edge damage and continuing movement affect the decision. A filled line should therefore not be taken as evidence that the slab’s underlying behaviour has been corrected.
For a room that will become an exposed concrete floor, ask for the assessment and proposed treatment to be described before choosing the final appearance. Keep any structural investigation or repair as an explicitly defined part of the project, with the appropriate person responsible for it.

- Left: blue material bridges the top of a crack in a simplified concrete cross-section.
- Right: if the sides move apart, the fill can be affected too. The arrows show relative movement.
Check whether the line is a joint
A straight groove or a line beside a wall may be an intentional joint. Its role matters more than whether you would prefer a continuous-looking floor. Do not ask for every visible line to be filled identically as part of polishing.
The National Ready Mixed Concrete Association’s guide to joints in concrete slabs on ground explains that contraction joints control where shrinkage cracking occurs. Isolation joints separate adjoining elements so they can move independently. Construction joints mark separate concrete placements and can have different design functions.
Ask the contractor to identify the joints, explain which will remain visible and specify how each will be treated. If drawings or earlier repair records exist, provide them. Where the function is uncertain, resolve that question before choosing a material simply because its colour matches the slab.
Why filling alone may not be enough
Imagine filling a narrow gap between two pieces of concrete. If those pieces later move apart, the material between them must accommodate that movement or the repair can be affected. Making the top look continuous does not by itself restrain the pieces below it.
The Concrete Society notes that previously filled floor cracks can develop fine cracks again where movement continues. This is why the treatment needs to suit the assessed condition, rather than being chosen only for its appearance on the day it is installed.
Grinding and polishing work on the surface. They do not establish that a moving crack has stopped. Likewise, mechanical levelling removes high concrete; it does not fill a gap, raise a low area or provide a structural repair. If more than one type of work is needed, the quote should identify each part.
Agree the order of work before anyone starts
The useful question is not simply whether a crack should be filled “before polishing”. Ask for a sequence that explains the initial inspection, any further investigation, surface preparation, proposed treatment and finishing. The timing must suit the chosen approach and the condition revealed during preparation.
Nominate who makes the next decision if removing an old covering exposes more damage. A clear arrangement lets you review the new information before the work expands. It also avoids assuming that an initial photograph captured every condition beneath the former floor.
Where a repair will be visible in the finished room, discuss a representative trial. That can help you judge the appearance, but it does not prove that the crack is no longer moving. For that separate appearance question, read why a flush repair can still look different after polishing.
What to ask before accepting a quote
Use the conversation to replace a general promise with an agreed scope. These questions help establish what is included and what needs a separate decision:
- Which lines are cracks, and which are intentional joints?
- What information or assessment is needed before treatment is selected?
- What is each proposed repair intended to achieve?
- Who is responsible for any further investigation or separate repair work?
- How will unexpected conditions affect the agreed work and timing?
- What appearance should be assessed in a trial, and which lines will remain visible?
Send the suburb, approximate floor area, existing floor covering, photographs and any repair history with your enquiry. Explain how the room will be used and the finish you are considering. Those details give the contractor a more useful starting point than a request to remove every crack.
Superfloor Australia can discuss your slab and the proposed polished concrete finish. Get in touch with the project details to discuss the next step.
